London based – Gas Safe Registered Plumbers, Fully Insured.Free Estimates, contact us by phone or by email.

Central heating installation
Boiler installation
Unvented cylinders
Solar domestic hot water
Power flushing
Bathroom design and installation
Showers installed
Exterior drainage installation
Sinks unblocked

Below every single plumbing fixture that drains into the house system is a trap containing a water seal, intended to prevent the return of foul gases from the sewer into the living areas of house or garden. The trap takes the form of a small U-shaped loop of pipe so formed that it is always filled with water. As new water drains from the fixture it displaces the water in the trap; part of the outgoing water then remains in the loop to replace the seal and maintain the barrier against air that would otherwise drift back up from the drainage pipes.

The primary purpose of a trap is to prevent contamination from the drains, but it also provides a convenient means of access to the pipes below the fixture. If you have to unblock a pipe you have an alternative to working through the plughole of the fixture. A trap is also a safety measure against the loss of small valuable objects that get accidentally washed down the plughole: a ring or a contact lens can often be found lying safely at the bottom of the U-bend, and can simply be tipped out once you have removed the trap. Traps in which the horizontal pipe leading from the U-bend gives a resemblance to the letter P are called P-traps. You will also often find S-traps, with a vertical pipe after the bend, and self-contained bottle traps (opposite page, below) whose neat appearance makes them particularly popular for use under wash basins or anywhere else where they are openly visible. Traps may be made in any of the normal plumbing materials, such as copper, steel, chrome or plastic. It is usually desirable that the material of the trap and the following waste pipe should match, but a new plastic trap can be satisfactorily fixed to an existing pipe of any material. The same technique is used for attaching traps of both matching and dissimilar materials.

When the water draining from one appliance wells up through the waste of another, the trouble probably lies in the main drain or its branches, which channel waste into the sewer. Since waste flows downwards, any blockage in the main drain or soil stack will stop up all the appliances above that point. In addition, anything that blocks the vent, which keeps air flowing through the system, will cause waste to drain away sluggishly, and there may be an unpleasant odour in the house. Before starting work, plot the course of the pipes in your waste system to help you pinpoint the blockage. You may find it helpful to sketch the layout on paper. Once you have decided where the obstruction might be, try a rubber plunger of the appliance closest to the trouble spot this can be effective even if the blockage is in the main soil and waste stack. If that fails, try cleaning out the stack with a cleaning rod or drain auger. Work from the appliance closest to the blockage.

To make the job easier, hire an electric auger up to 30 metres long from a tool-hire firm. Even an electric auger, however, will not work effectively if it has to go round too many bends. Always take the straightest possible route to the problem area. In the main stack that usually means working through the nearest inspection chamber or, more commonly, through a cleaning eye. A blockage below ground level, in the drain to the sewer, will have to be reached through a gully or inspection chamber.
In most plumbing repairs speed is essential, but unclogging the main drains calls instead for patience. Avoid precipitate action. The column of water trapped by the blockage may extend above the point where your cleaning eye is located, and it will gush out as soon as you open the eye. Wait for at least two or three hours after you have spotted the trouble before starting work, to allow as much as possible of the waste to seep past the blockage. Even then, you will need mops, buckets, rags and old newspapers to soak up any overflow. When you have finished clearing up, dispose of the rags and newspapers in sealed plastic bags and disinfect the site.

Locating the blockage
The first step in finding blockages is to check which fittings are draining normally; clogs in a soil and waste stack will always be below the level of the lowest blocked fitting and above the highest working fitting. In the plumbing system above, a blockage near the cleaning eye would block both the basin and the W.C., but not the bath. Should all the first-floor fittings be blocked, the problem must lie below the point where the bath waste feeds into the stack. In either case, the blockage should be cleared through the cleaning eye. If the sink on the ground floor is blocked, the fault must lie in the gully or the pipes leading to or from it. Try pouring water through the gully. If it passes freely through, the blockage is in the sink waste, which should be cleared through the sink trap; if not, clear the gully with a hose or auger. When all the appliances are blocked, the blockage must be in the drain to the public sewer, and should be tackled through the inspection chamber. Often the first sign of such an obstruction will be flooding from the gully, the lowest drain outlet in the system.

Working through the cleaning eye
If the trap under the clogged fixture has a cleaning eye, place a bucket under the trap and remove the threaded eye. After water has emptied from the trap and sin-k, straighten a wire coat hanger, form a small hook in one end, and probe through the trap. If the obstruction is near the opening, you should be able to dislodge it or hook it and draw it out. If not, feed a drain auger first up to the sink opening, then through the back half of the trap. If the blockage is not in the trap, try cleaning beyond the trap .

Removing a trap for cleaning
If the trap has no cleaning eye, shut off the water, unscrew the nut that attaches the trap to the threaded sink waste and detach the trap. Clean it with detergent and a bottle brush. To clear a modern bottle trap, unscrew the bottom half of the trap and probe the fixture . Reassemble the trap and turn on the water.

Augering branch drains
With the trap removed, wind a drain auger into the exposed end of the pipe. The blockage may be in the vertical pipe behind the fixture or in the near-horizontal pipe that connects with the main stack serving the entire house. If the auger goes freely through the waste pipe until it enters the stack, the blockage is probably in a section of the main drainage system, in which case you should clear it. If your waste pipe is made of push-fit plastic sections and is readily accessible, you may be able to dismantle it section by section until you reach the blockage, emptying out any water the pipes contain into a bucket as you go.

Unblocking Bath Wastes
The techniques for unblocking bath wastes are the same as for sinks and basins, except that the trap on a bath-hidden away at floor level behind the side panels of the bath-is usually more difficult to reach than that of a sink or basin. As with sinks and basins, a rubber plunger is the first tool to try. Block up the bath’s overflow opening with a damp rag so that the force from the plunger is not dissipated upwards. Use the plunger as a plug and make sure that there is enough water in the bath to cover the cup completely, then pump the plunger vigorously up and down. If the blockage does not disperse immediately, persevere: the force transmitted from the rubber cup through the water in the pipe may be pushing the obstruction along the waste pipe by degrees, until it breaks down or is freed by being ejected into a main pipe of larger diameter.

If the plunger does not succeed, try a drain auger. The blockage is most likely to be in the trap and it should be possible to remove it by working with the auger through the plughole. If, however, the blockage lies in a branch drain beyond the trap, it may be necessary to remove the trap. To gain access to the trap, you will have to remove a side or end panel from the bath. Bath panels come in many variations, but they generally conform to one of two basic types. The panel may be made of hardboard or plywood, and held in place near the edges, usually with domed mirror screws, In that case, unscrew and remove the domed tops of the screws by twisting them anticlockwise; underneath you will find the slotted heads of the screws that fix the panel to the bath. These are simply removed with a screwdriver. Other baths have moulded plastic panels which are flexible enough to be slotted into place under the lip of the bath. Remove such panels by bending them until you can slip the top edge out from its mooring. Then unscrew or dismantle the trap.

Unblocking W.C.s – toilets

Using o plunger
If a blocked W.C. pan is full to the rim, empty out half its contents. If the pan is empty, add water up to the normal level. Fit a large rubber plunger over the wide opening near the bottom of the pan. Pump 10 times with short, rapid strokes, then lift the plunger quickly. If the blockage has been cleared, you will hear a gurgling sound and the water in the pan will return to its normal level. If the water level sinks slightly but not down to the normal level, the blockage has been only partially removed, in which case you will need to pump again. When you think you have completely cleared the obstruction, test by flushing the W.C.

Using a W.C. auger
Add or remove water as necessary. The W.C. auger-designed specially for clearing W.C.s-has a cranking handle attached to a long sleeve, shaped to guide the auger directly into the trap. Hold the sleeve firmly near the top and wind the hook slowly clockwise into the trap until you reach the obstruction.

From time to time , we get jobs like these. We are the last on the plumbing and pest control list and the most effective solution. Most people will try the cheapest solutions before they actually deal with real problem. You have rats in your home. In London , most plumbers can run a pipe for you, unblock a drain, etc – but not many actually understand how the drains work.
There is no easy way to say it, a rat and a mouse is attracted by human feces. If the soil under the building or around the building has been contaminated, the pests will consider your toilet, WC and building itself – an attractive place.

Human feces also known as stool, is the waste product of the human digestive system including bacteria.A very unpleasant job and also dangerous from a health point of view. Most people go for the cheapest option, installing rat traps, poison, etc. The cost of getting rid of bad smell and rats, can be reduced if we are the first on the job. Customers are spending thousands of pounds sometimes, before they call us.
Our plumbers and builders are not delicate people, we keep it simple. We make sure that we get rid of the smell and not even an insect can crawl up from the ground up.

Removing feces contaminated soil

Using CCTV camera , rat traps,etc- the drain is still there, the problem will not go away, sealing the smell will be just a temporary solution.

When you have a drain problem, don’t just cover it up and look for easy solutions, it won’t go away.

Plumbing means pipes, which can be unsightly if left exposed. Boxing them in will tidy up the look of the home. Whichever method you choose to conceal pipes, the first task is to strip the wall around the pipes so a supporting frame can be securely fixed. Make sure the pipes are in good condition and that the joints are well made. Check compression joints for tightness and, if there is any corrosion, remake the joints. Before boxing in make sure the pipes are fixed securely to the wall with pipe clips.

Boiler boxed in – cupboard

Where pipes come through the floor from a room below, seal the gap between the pipes and the floor with a shaped piece of 12 or l8mm chipboard to reduce the risk of fire spreading. Pipes on an outside wall should be insulated with a glass fibre blanket or with shaped foam secured with tape.

Making the box
Using plugs and screws fix 25 x 19mm timber battens vertically to the wall on each side of the pipes; check with a plumb line to ensure accurate positioning. Where the pipes are on an open wall, glue and screw or pin 12mm thick plywood or chipboard to the sides of the battens (the width of the timber side pieces depends on the depth required for the box). Where the pipes are in a corner you will need only one side piece and, if the pipes protrude less than 50mm from the wall, you may not need side pieces at all. In this case use 25mm battens, wide enough to clear the pipes, as side pieces.

Front panel
Cover the pipes with 3 or 5mm hardboard or plywood; if you want a more solid panel, use 12mm chipboard. Don’t glue the front panels in place because you must have access to the pipes in case of leaks. Fix hardboard or plywood with panel or hardboard pins and secure chipboard with countersunk screws. You will achieve a better finish if you cut your front panel slightly oversize and trim it back with a plane once it is fixed in position. Use a cellulose filler to fill any cracks and countersunk screw heads, except where these provide access. Give the box a coat of primer before decorating as required. When decorating, make sure you do not cover the join or your decorations will be spoiled when you need to remove the box.

Stopcocks and draincocks
Where there are stopcocks or draincocks in the pipe runs you must cut holes in the front panel to allow the handles to protrude, unless you fit access covers in the boxes. Alternatively construct a box which can be easily removed. Make up a hardboard box of the required size, using 25mm square battens at the front corners to give it form. On the inside face of the front panel glue 19mm wide battens at approximately 1m intervals and secure them with panel pins hammered through from the outside. Screw Terry clips of the required size, according to the pipe dimensions, to the battens; these will snap over the pipes and secure the panel.

Disappearing pipes
Where pipes disappear into a wall, the bottom or top (as applicable) of the box can be finished at an angle. Cut the side pieces and/or battens at 45 degrees, pin a small piece of hardboard or plywood to the sloping part and plane across the front panel until it forms a neat joint.

Alcove pipes
When you wish to conceal pipes in an alcove it is often best to cover the entire wall area with a full width panel; this robs you of little space and does not affect the look of the wall line. Fix timber battens on each side of the pipes, as previously explained. Plug and screw a piece of batten on each side of the alcove level with the front of the battens on each side of the pipes. Use 9mm ($in) chipboard, fixed with countersunk screws, to conceal the pipes and to provide easy access and nail 9.5mm plasterboard either side of the chipboard.
You can use the same method, but with a stronger framework, to conceal cisterns and soil and water pipes.

Skirting board pipes

Screw a batten to the floor with its face just in front of the maximum projection of the pipes. Glue and screw a 12mm facing board to the batten, then glue and nail scotia moulding to the top of the facing board. Finally glue and pin a strip of hardboard or plywood between the moulding and the top of the skirting. If you want a round edge finish, use a facing board of the same height as the skirting; glue and pin a length of 12mm board to the top of the facing board and skirting and round the front edge with a plane. Although a certain amount of time, effort and money is involved, you will be surprised how much neater rooms will look when the pipes have been boxed in. You can paint or wallpaper the covering.

If, in spite of your precautions, a freeze-up does occur, it is essential to deal with it immediately. If there is any delay the plug of ice will spread along the pipe and increase the risk of damage. You can gauge the position of the freeze-up from the situation of the plumbing fittings which have stopped working. If, for instance, water is not flowing into the main cold water storage cistern but is running from the cold tap over the kitchen sink. the plug of ice must be in the rising main between the branch to the kitchen sink and the cistern. Strip off the lagging from the affected pipe and apply heat – either with cloths soaked in hot water and wrung dry or a filled hot water bottle. If a pipe is inaccessible direct a jet of warm air towards it from a hair dryer or the outlet of a vacuum cleaner. Fortunately copper tubing conducts very well and a small plug of ice can often be melted by applying heat to the pipe about a metre from the actual location of the ice.

Burst pipe
If the freeze-up results in a burst pipe the first indication will probably be water dripping through a ceiling, since pipes in the loft are most likely to burst; wherever the leak, immediate action is vital. Turn off the main stopcock and open up every tap in the house. This will drain the cistern and pipes and reduce the damage. When the system is completely drained,find the position of the leak.

Damaged copper piping
If you have copper piping, you will probably find a compression or soldered capillary joint will have been forced open by the expansion of ice. All you need to do in this case is fit a new joint. Copper piping does sometimes split under pressure. If that happens, you will have to cut out the defective length and insert a new length. An easy way of doing this is to insert a repair coupling. Cut out the damaged section of pipe with a fine tooth hacksaw leaving a gap of not more than 89mm between the pipe ends. Remove the burr from the tube ends with a small file. One end of the coupling has a tube stop, the other is free to slide along the pipe. Slacken the nuts of the coupling, spring one end of the pipe out just enough to allow you to slide the repair coupling over it. Line it up with the other pipe end and push the coupling on to it until the tube stop is reached. Unscrew the nuts and slide them and the copper jointing rings along the pipe. Apply jointing compound or gloss paint into the bevels of the fitting and around the leading edge of the jointing rings. Tighten the nuts with a spanner so the tube is lightly gripped; make another turn, or a turn and a quarter, making sure you do not overtighten.

Burst lead pipe
The orthodox and approved of copper pipe and fitting method of repairing a burst lead pipe is to cut out repair coupling. Making the affected length and replace it with a new length temporary repair to lead pipe of pipe; this job is best left to an expert plumber. You can,however,make a temporary repair with one of the epoxy resin repair kits available. Dry the affected length of pipe thoroughly and knock the edges of the split together with a hammer. Rub down with abrasive paper. Make up the resin filler according to the manufacturer’s instructions and apply it round the pipe to cover the split and the surrounding area. While the filler is still plastic, bind round it with a glass fibre bandage and ‘butter’ a further layer of resin filler over the bandage. When thoroughly set, rub down with abrasive paper to make an unobtrusive joint. You will be able to use the pipe again within a few hours.

If the plumbing system in your home is not adequately protected, severe weather can cause water to freeze in the pipes, producing blockages and burst pipes. You can deal with these yourself, but it is better to prevent any damage by checking your anti-frost defences every autumn.

Protecting plumbing
Frost protection is built into the structure of a well designed, modern home and the important design points are explained be1ow.

Service pipe
This pipe conveys water from the water authority’s communication pipe to the house and should be covered by at least 750mm of earth throughout its length. If it enters the house by a hollow, boarded floor, it should be thoroughly protected from draughts. The pipe should be taken up into the roof space to supply the cold water storage cistern – against an external wall.

Storage cistern
The cold water storage cistern is best situated against a flue which is in constant use. To prevent icy draughts blowing up the warning pipe leading from the cistern. you can fit a hinged copper flap over the outlet; there is, however, a risk that this will jam in the open or closed position. A better method is to extend the pipe within the cistern and bend it over so its outlet is about 38mm below the surface of the water. There are gadgets, such as the frost guard, which make it easy to extend internally the warning pipe from a storage or flushing cistern. The boiler. hot water storage cylinder and cold water storage cistern are best installed in a vertical column so the vulnerable cold water cistern receives the benefit of the rising warm air. All lengths of water pipe within the roof space should be kept short and well away from the eaves.

Lagging
Efficient lagging of storage tanks and pipes reduces the rate at which water loses its warmth and protects pipes exposed to cold air; but it cannot make up for a bad plumbing design and it will not add heat to the system. Pipes to lag are those against external walls, under the ground floor and in the roof space. Don’t omit the vent pipe of the hot water system since the water in this pipe is not as hot as that in the rest of the system and, if it freezes, it can create a vacuum which could damage the cylinder. There are several types of pipe lagging available and it is best to use inorganic materials. These include wrap-round glass fibre; moulded polystyrene (which comes in rigid sections which fit round the pipe) and flexible moulded foam plastic (which you split open to fit round the pipe).

Polystyrene is rather awkward to use, but is good for underground pipes since it does not absorb water. The moulded types of lagging come in a variety of sizes to fit different pipes. so make sure you buy the appropriate size. Whichever type you use. make sure you lag behind pipes against external walls to protect them from the cold wall. Cover the tails of ball valves and all but the handles of stopcocks and gate valves; if you are using rigid lagging sections, you will need some of the wrap-round type for these areas. Bind wrap-round insulation round the pipe like a bandage, overlapping it to prevent gaps, and secure it with string or adhesive tape. Where a pipe joins a cistern, make a full turn and tie it to hold the end in place. When joining two lengths overlap and tie securely. If you lag the pipes before fitting them there is of course no need to slit the lagging: you can slide the pipe length through it. Where pipes go through a wall make sure the insulation goes right up the wall.

You also need to protect the cold water cistern. The easiest way to cover a square cistern is to use fire proof insulation slabs. For a circular cistern use glass fibre tank wrap. If you have insulating material between the floor joists in the loft, make sure the area immediately below the tank is left uncovered so warn air is allowed to reach the tank’

A form of electrolytic corrosion can take place in a central heating system where copper tubing is used in conjunction with pressed steel radiators. Some air – a prerequisite of corrosion – will always be present in the system; it dissolves into the surface of the water in the feed and expansion tank and may also enter through minute leaks too small to permit water to escape. Electrolytic corrosion within a central heating system results in the formation of black iron oxide sludge (magnetite) and hydrogen gas. This leads to impeded water flow and radiators will need continual venting to release airlocks to keep up the required heat level. The iron oxide sludge is drawn towards the magnetic field of the circulating pump and its abrasive qualities contribute towards early pump failure. Also the metal of the radiators, from which the magnetite and hydrogen are produced, becomes thinner until leaks eventually develop in the radiators. Removing airlocks by venting the radiator is a simple process. A key supplied for this purpose is inserted in the radiator when the water is warm and turned anti-clockwise to open the vent valve. Hold a container underneath the key since some water may escape when the valve is opened. Air will come out of the radiator – when it stops doing so and water begins to flow you should tighten the valve. If a radiator in your heating system needs to be continually vented, it is worth testing for internal corrosion while you are carrying out this operation. Apply a lighted taper to the gas escaping from the radiator; hydrogen gas burns with a blue flame and indicates the presence of corrosion.

Protection treatment
A chemical corrosion-proofer can be introduced into the feed and expansion tank to protect the system against corrosion. It is best to do this when the system is first installed, but it can be carried out with an existing system; it will not, however, undo damage already done. Before introducing a corrosion-proofer into an existing system you should get rid of any magnetite sludge with a special solvent. Like the corrosion-proofer, this is introduced into the feed and expansion tank and you should drain the system first. Disconnect the fuel supply to the boiler and switch off the ignition system several hours before draining to give the water time to cool. Tie up the ball float arm of the feed and expansion tank and fit a hose to the draincock near the boiler, running the hose to a drain outside. Undo the draincock empty the system and, when you have closed the draincock, free the ball float arm in the feed and expansion tank. Allow the system to refill, introducing the solvent at the same time. Follow the manufacturer’s instructions for the length of time you should allow for the solvent to complete its work before carrying out treatment with the corrosion-proofer.

Some plumbing fittings are subject to corrosion. When this occurs, they are weakened and eventually leaks develop. There are several ways of preventing this happening in your system. Modem galvanized steel water storage cisterns frequently show signs of rust within a few months of being installed. Older plumbing systems, which were constructed entirely of lead or galvanized steel, could generally be expected to last, without this kind of deterioration, for 50 years or more. In modern systems the use of copper, which itself virtually never corrodes, has greatly increased the risk of corrosion to any galvanized iron or steel fittings incorporated in the system. The process which gives rise to this corrosion is known as electrolytic action.

This is the same principle on which the simple electric battery cell is based; where rods of zinc and copper are in electrical contact with each other and are immersed in a weak acid solution which is able to conduct an electric current (an electrolyte), electricity will pass between the rods, bubbles of oxygen will be produced and the zinc rod will slowly dissolve away. A plumbing system in which copper water supply and distribution pipes are connected to a galvanized steel cold water storage cistern or hot water storage tank, may reproduce these conditions; the copper tubing and the zinc coating of the galvanized steel are in direct contact and the water in the cistern or tank, if very mildly acidic, will act as an electrolyte. This results in rapid failure of the protective galvanized coating allowing aerated water to penetrate to the vulnerable steel underneath; eventually rust will form. A particular form of electrolytic corrosion may result in damage to brass plumbing fittings, such as compression joints and stop valves. Brass is an alloy of copper. and zinc; electrolytic action may result in the zinc in the fittings dissolving away to leave them unchanged in appearance but totally without structural strength. Where these fittings in your plumbing system are showing signs of leakage, it would be worth checking with a local plumber if the type of water in your area is likely to create a situation favourable to electrolytic corrosion. If so, you should replace brass fittings with fittings made of gun-metal (an alloy of copper and tin), which is not susceptible to this kind of damage.

Corrosion as a result of electrolytic action is also likely to occur in pipework if a new length of copper tubing is fitted into an existing galvanized steel hot or cold water system. Always use stainless steel tubing instead – this is not liable to the same risk.

Protecting cisterns and tanks
There are steps you can take to prevent corrosion in galvanized steel cisterns and tanks. For example, when you are installing a new cistern or tank, it is important to make sure you remove every trace of metal dust or shaving resulting from drilling holes for tappings. The least fragment remaining will become a focus for corrosion. One way of protecting a cold water storage cistern is to ensure the metal of the cistern does not come into direct contact with the water it contains. This can be done by painting the internal surfaces with two coats of a taste and odour-free bituminous paint to prevent these surfaces from rusting. Before applying this treatment to a new tank, cut holes for the pipe connections: when you are painting. pay particular attention to the areas in the immediate vicinity of these holes.

Galvanized steel hot water storage tanks, which can still be found in many older homes, cannot be protected by this paint treatment.

Cathodic protection
A sacrificial magnesium anode which dissolves instead of the zinc coating will protect both galvanized steel cold water storage cisterns and hot water tanks. With a cold water storage cistern, clamp the copper wire attached to the anode to the side of the cistern using a G-clamp and suspend the wire over a timber batten into the water in the middle of the cistern. Make sure you replace the anode before it dissolves completely. When protecting a hot water tank, fit the anode to the hand-hole cover of the tank. Turn off the water supply and drain the system from the draincock beside the boiler; unscrew the bolts retaining the hand-hole cover and remove it. Drill a hole in the centre of the cover, use abrasive paper to rub down the area of metal around the hole and screw in the anode before replacing the cover.